Automotive Bumper Uses a Plastics Based Lightweight Solution

Audi R8 complete bumper module, from a well known manufacturer of exterior and interior plastics components for the automotive industry, meets the most stringent requirements.

Among top-of-the-range cars, the Audi R8 represents supreme dynamics, cutting-edge technology and exhilarating styling. The mid-engine sports car’s extravagant design features include two large air apertures at the rear. The rear automotive bumper was designed using a lightweight plastics based solution that had to meet the most stringent requirements, particularly in terms of precision fit and surface quality. The plastics material also had to be extremely tough to ensure that the bumper was resistant to minor collisions. "In order to meet the complex requirements profile, we joined forces with our partners WAYAND, Quarzwerke and Audi to formulate a solution based on a customized grade of our polyurethane system Bayflex* 180," explains Dieter Gaumitz, an expert in polyurethane bodywork parts at Bayer MaterialScience AG. The complete bumper module is supplied by Idar-Oberstein-based WAYAND GMBH Kunststofferzeugnisse, a well known manufacturer of exterior and interior plastic components for the automotive industry.

The rear of the automotive consists of three components: the rear panel, which is connected to the retractable rear spoiler; the cover, which incorporates the apertures of the two twin tailpipes and the mounts for the transverse struts of the two air apertures; and the diffuser with integrated rear fog light that extends down to the underbody of the car. The cover and the diffuser are known as the rear bumper assembly. This assembly spans an area of approx. 2 square meters. Because of its size alone, manufacturing it in polyurethane constitutes a major feat of design and processing.

The cover and the diffuser are known as the rear bumper assembly. Because of its size alone, an assembly span area of approx. 2 square meters, manufacturing it in Bayflex 180 constitutes a major feat of design and processing. See photo at right.

A special ingredient in the Bayflex 180 material grade used is the finely ground reinforcing material Tremin** 939-304, which is produced for the R8 by Quarzwerke GmbH in Frechen. It helps to produce an excellent component surface and an outstanding paint finish. The plastics material also ensures that the polyurethane system remains extremely tough over a broad temperature range from -30 °C to 150 °C, thus rendering the rear bumper highly resistant to stone impact.

The requirements for precision fit were particularly high in the area of the rear automotive panel and the cover, to allow the design of optically impressive narrow gap dimensions (the "zero-gap look"). "The minimal thermal expansion of Bayflex 180 proved to be an advantage. It is comparable with that of aluminum," says Gaumitz.

Another strength of the polyurethane system is its outstanding flow behavior, which opens up a wealth of design options. It is possible to produce large, thin-walled plastics components with complex geometries economically using Reinforced Reaction Injection Molding (R-RIM) technology. The wall thicknesses can be varied as required. In the case of the rear bumper and the rear panel (the latter also being produced from Bayflex 180), they are between 2 and 5 mm near the attachments, otherwise they average around 3.3 mm.

Bayflex 180 has a heat resistance of more than 150 °C. This high thermal stability allows rear panels, for example, to be fitted very close to heat-emitting automotive exhaust systems.

Bayer MaterialScience contributed an extensive range of services to the joint development work with Audi, WAYAND and Quarzwerke. For instance, it determined those polyurethane parameters that are governed by the rate of elongation by conducting high-speed tensile tests on specimens. This enabled the strength, energy absorption and dynamic load resistance of the rear bumper to be calculated using standard simulation programs and the crash behavior to be evaluated reliably and realistically. The service also included plastics mold flow calculations for optimization of the flow behavior and the gate design.

About BaySystems*:
With effect from March 1, 2007, Bayer MaterialScience has combined its entire global polyurethane systems business under the umbrella brand of BaySystems. This change affects not only existing product brands in this segment - including Bayflex - but also the global network of polyurethane systems houses.

* Bayflex and BaySystems are registered trademarks of Bayer MatieralScience AG, a Bayer Group company, and is one of the world's largest polymer companies.
** Tremin is produced for the R8 by Quarzwerke GmbH in Frechen.

Read a recent press release about - Polyurethanes Business Unit of Bayer MaterialScience CentralEurope extends its global network of polyurethane systems houses by acquiring Brahe in the Czech Republic.

Manufacturing/Quality

How to Lead a Business Process Improvement Effort
CEU Credits: 1
It's the essential business process improvement guide for executives, managers, and supervisors.

Purchase This Course!

Click here to view more current news.